English
Español 
Português 
русский 
Français 
日本語 
Deutsch 
tiếng Việt 
Italiano 
Nederlands 
ภาษาไทย 
Polski 
한국어 
Svenska 
magyar 
Malay 
বাংলা ভাষার 
Dansk 
Suomi 
हिन्दी 
Pilipino 
Türkçe 
Gaeilge 
العربية 
Indonesia 
Norsk 
تمل 
český 
ελληνικά 
український 
Javanese 
فارسی 
தமிழ் 
తెలుగు 
नेपाली 
Burmese 
български 
ລາວ 
Latine 
Қазақша 
Euskal 
Azərbaycan 
Slovenský jazyk 
Македонски 
Lietuvos 
Eesti Keel 
Română 
Slovenski 
मराठी 
Srpski језик
The maintenance and repair measures of the fog machine
2023-02-08
The fog machine is composed of base, control appliance, fan, high pressure pump and other parts. The fan used on the dust fog machine is usually an axial flow fan. Because the axial flow fan has the advantages of large air volume, high efficiency, soft and uniform wind speed, large spraying range and long range, it becomes one of the main parts of the dust fog machine. It is composed of wind cylinder, water spray ring (nozzle), wind blade, motor, etc. Its quality affects the efficiency and fogging effect of the fog machine. The fog cannon machine relies on the airflow from the fan to break the atomized droplets so that the droplets can penetrate the dust and achieve the effect of dust suppression.
The wind blade of the fog cannon machine is generally made of aluminum alloy, which has light quality, stable operation, sufficient pressure and high wind power. The nozzle directly determines the merits of the fogging effect, and the good nozzle is generally made of 304 stainless steel, which is wear-resistant and corrosion-resistant, and the water mist is evenly sprayed, which will not cause a large amount of water on the ground of the material yard, especially to avoid large area of ice in winter, which will affect the operation surface and also will not form secondary pollution of the environment.
Dust fog machine can be used for garden trees, street trees, seedlings, nurseries for pest and disease spraying and prevention, agricultural and forestry pest and disease spraying and prevention, disinfection and epidemic prevention after major natural disasters, stations, docks and airports, public places, garbage sites, farms sterilization and disinfection, sanitation and epidemic prevention, but also garden watering, tree spraying, green belt spraying, lawn spraying, urban road sprinkling and cooling, construction dust reduction, coal dust pressure, mining dust pressure, mining road surface. Mining dust pressure, mining road dust removal, factory dust removal, etc. The fog machine plays an important role in environmental protection.
The use of fog machine machine to environmental protection work has brought a lot of convenience, but in use in order to make its life longer, should do a good job of daily maintenance work.how do we maintain the fog machine in daily use?
First, according to the manual operation.
According to the machine manual, check and adjust the technical state of the components, to the lubrication points lubrication. To keep clean, remove mud and dirt in a timely manner.
Second, ensure daily cleaning
After the end of the daily spraying operation, spray with water for a few minutes, clear the residual liquid in the liquid tank, liquid pump and pipeline, remove the mud and dirt in time, and remove the clean water.
Third, regular maintenance
Every three months, open the electronic control panel on the independent operation mode, the fan, water pump, heating tape for maintenance.
Fourth, check the oil level
Every week, check the oil level of the pump machine to ensure that the oil level is just at half of the oil probe cover.
Fifth, Oil change
The oil must be replaced once a month when the pump runs cumulatively. Every week, tighten the grease cup cover clockwise for two turns.
Sixth, When the pump belt is running with obvious jumping, rotate the tensioning bolt and tension the belt.
Seventh, According to the actual use, clean the filter device regularly.
Eighth, Stable storage of fog machine
In the winter or fog gun idle, if you need to park for a long time, to the liquid tank, liquid pump and pipeline and other water to clean, and remove the v-belt, spray hose, nozzle, mixer and suction pipe and other parts, placed in a cool dry place, the room without dust. Fog machine can not be corrosive strong items (such as fertilizers, pesticides, etc.) stacked together. In order to prevent rust damage, rubber parts are generally hanging on the wall, can not be squeezed and folded.
To sum up, the fog machine also needs us to maintain from time to time. Whether in the process of use or need to be stored, it is necessary to use the correct method. Only then can the dust fog machine life longer, so that the equipment does not suffer damage, and better for our services.
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies.
Privacy Policy